A851GOT-LBD A851GOT-LBD-M3 Touch Screen Protective Film
Mitsubishi GOT-A800 A851GOT series HMI A851GOT-LBD A851GOT-LBD-M3 HMI Touch Glass Front overlay Repair Kit.
The communication units for the GOT800 A851GOT series Touch screen panel front overlay and A77GOT series listed below require settings with rotary switches and others on the hardware. However, the communication units for the GOT1000 series do not have rotary switches and others, and settings with the drawing software or the utility are required. The communication modules and options for the GOT800 series and A77GOT series shown in the following list have no alternative GOT1000 series models. If you have difficulty to replace the A851GOT-LBD A851GOT-LBD-M3 touch screen panel front overlay modules and options with the GOT1000 series, keep enough spares.
The connectors for the GOT800 A851GOT A851GOT-LBD A851GOT-LBD-M3 touch glass front overlay series serial communication module (RS-232) and for the GOT1000 series serial communication port (RS-232) are the same type (9-pin D-sub (male), with inch screws). The A851GOT-LBD A851GOT-LBD-M3 pin locations are also the same. Use the Mitsubishi GOT1000 series cables (including user-created cables described in GOT1000 Series Connection Manual) to connect to the GOT1000 series.
The table below describes the parameters of the A851GOT-LBD A851GOT-LBD-M3 Mitsubishi A851GOT Touch Glass Overlay.
|Part Number:||A851GOT-LBD A851GOT-LBD-M3|
|Display device:||STN monochrome LCD|
|Screen diagonal:||5.7 in|
|Product Line:||Mitsubishi A851GOT Series|
|Input Power:||24VDC (+10%, -15%)|
|Operating Temperature:||0 to 55°C|
|Resolution:||320 x 240 dot|
|Storage Temperature:||-20°C to 60°C|
Related Mitsubishi A851GOT Series Part No. :
|Mitsubishi GOT-A800||Description||Inventory status|
|A851GOT-LBD||Mitsubishi GOT-A800 Touch Screen Monitor Overlay Repair||In Stock|
|A851GOT-LBD-M3||Touch Screen Protective Film Mitsubishi GOT800 A851GOT||Available Now|
|A851GOT-LWD||Mitsubishi A851GOT Touch Screen Glass Front Overlay||In Stock|
|A851GOT-LWD-M3||Mitsubishi GOT800 A851GOT Touch Protective Film||In Stock|
|A851GOT-SBD||Mitsubishi A851GOT Touch Screen Overlay Replacement||In Stock|
|A851GOT-SBD-M3||HMI Panel Glass Overlay GOT-A800 A851GOT Repair||Available Now|
|A851GOT-SWD||Mitsubishi GOT800 Front Overlay Touch Panel Glass||In Stock|
|A851GOT-SWD-M3||Mitsubishi GOT-A800 Touch Screen Protective Film Repair||Available Now|
|Mitsubishi A851GOT HMI||Description||Inventory status|
Mitsubishi GOT-A800 Series HMI Manuals PDF Download:
Question: What is the size of A851GOT-LBD-M3 Touch Screen Panel Glass?
Answer: The Mitsubishi GOT-A800 A851GOT A851GOT-LBD-M3 touch panel is 5.7-inch.
Question: What is the procedure to replace the A800 Series A851GOT-LBD backlights?
(2) Using a screwdriver, remove the six securing screws from the back of the GOT.
When the screws have been removed, remove the case of the control circuit section from the case of the display module.
(3) Remove the six screws securing the display module in place.
When the screws have been removed, remove the display module from the case.
(4) Turn over the display module, and disconnect the backlight cable connectors from the display module connectors (in two places).
For the SNT type remove from two locations on the top and bottom of the display module, and for the TFT type remove from one location on the top of the display module.
Take the two backlights off of the display module.
For the SNT type remove two backlights form the top and bottom of the display module, and for the TFT type remove one backlight from the top of the display module.
(5) install the new backlights by reversing the above procedure, and fit the display module back into its case.